Why Water Is the Real Medium
In watercolour, water does most of the work. The pigment just goes where the water takes it. Most beginner frustration (blotchy patches, pale washes, runs you didn't want) comes from too much water or too little, not from a lack of talent.
Three separate sources of water decide what happens on the page:
- Water in the brush. How much liquid the bristles hold.
- Water in the paint. How diluted the puddle on your palette is.
- Water on the paper. Whether the surface is dry, damp or wet.
On dry paper, a stroke stays where you put it and has a crisp edge. On wet paper, the same stroke spreads out and softens. This lesson is about controlling the first two: the brush and the paint.
Know Your Brush
Pick up the round brush from Level 1 and find its three working parts:
- Tip. The fine point at the end. It paints thin lines and dots.
- Belly. The fat middle of the hair bundle. It holds the water and paint, and it makes wide marks when you press down.
- Ferrule. The metal collar that holds the hairs. Keep paint below it, because paint that dries inside the ferrule spreads the hairs and wrecks the point.
Task 1: Mix Paint to the Right Strength
Painters describe the strength of a mix by comparing it to drinks and foods from the kitchen:
- Tea. Lots of water, a little pigment. Pale and see-through. Good for skies and first layers.
- Milk. About equal water and pigment. The everyday strength for most painting.
- Cream. More pigment, less water. Rich, strong colour.
- Butter. Very little water. Thick and close to opaque. Used for small dark details.
DO: In three wells of your palette, mix one colour at tea, milk and cream strength. Paint a small swatch of each on scrap paper.
Remember: watercolour dries noticeably lighter than it looks while wet. Always test a mix on scrap paper and let it dry before you judge it. If the dried swatch is too pale, mix it stronger.
Task 2: Load the Brush to the Right Wetness
The brush needs a different amount of water for each job.
- Dip the brush in clean water so the whole belly is wet.
- Touch it into your paint puddle and roll it gently so the belly takes up colour.
- Adjust the wetness:
- Too wet (drips or floods the paper): drag one side of the brush across the rim of your water jar, or touch the belly briefly to a folded tissue or kitchen towel.
- Much drier (for scratchy, broken marks): hold the belly against the tissue for longer.
- Wet and juicy (for wide areas of colour): skip the blotting step.
- Check by painting a stroke on scrap paper. A puddle that sits on the surface and looks shiny means too wet. A stroke that skips and breaks up means fairly dry.
Why it matters: if you touch a very wet brush into paint that is half dry, the extra water pushes back into the drying area and leaves a cauliflower-shaped mark called a backrun (or bloom). To avoid it, blot the brush until it is no wetter than the surface you are touching.
DO: Load the brush three times (juicy, medium, nearly dry) and paint one stroke with each. Write the wetness under each stroke.
Task 3: Make Different Marks with Pressure, Angle and Grip
One round brush can make many different marks. You change three things:
- Pressure. Light pressure uses only the tip and gives a thin line. Pressing down spreads the belly and gives a thick line.
- Angle. Holding the brush upright, at 90° to the paper, gives the finest control. Tilting it low lets the side of the belly sweep a wide stroke.
- Grip. Holding the brush close to the ferrule gives precise, small marks. Holding it further up the handle gives looser, freer strokes.
DO: Fill one sheet of scrap paper with these rows:
- Thin lines. Hold the brush upright and touch only the tip to the paper. Pull ten fine lines.
- Thick lines. Press down until the belly spreads. Pull ten wide strokes.
- Tapered strokes (thick to thin). Start light, press down in the middle, and lift off at the end, so the stroke swells and then narrows. Practise until the change in width looks smooth.
- Dots. Touch the tip down and lift straight up. Then try pressing a little harder to make bigger dots, as in leaves or petals.
- Side strokes. Lay the brush at a low angle and drag the side of the belly across the paper.
Keep the paint at milk strength so you are only changing how you use the brush.
Task 4: Paint a Dark-to-Light Value Strip
A value is how light or dark a colour is. This exercise trains you to control strength just by adding water.
- Draw a row of six boxes in pencil, each about 3 cm square.
- Mix a strong, cream-strength puddle of one dark colour.
- Fill box 1 with this strong mix.
- Rinse the brush, carry one brushful of clean water to the puddle, and stir. Fill box 2.
- Add another brushful of water, stir, and fill box 3.
- Repeat for boxes 4 and 5. Each box should look a step lighter than the one before.
- Fill box 6 with clear water only, which leaves the white paper.
- Let the strip dry completely and look at it. If two neighbouring boxes look alike, paint the strip again and add more water at each step.
Tip: stir every time you add water. Pigment settles quickly, so an unstirred puddle gives uneven boxes.
Key Takeaways
- Water in the brush, the paint and on the paper decides what happens on the page.
- Describe mix strength as tea, milk, cream or butter, and test mixes on scrap paper because watercolour dries lighter.
- Take water off the brush by dragging it on the jar rim or touching it to a tissue.
- Match your brush wetness to the surface to avoid backruns.
- Light pressure with the tip held upright makes thin lines. Pressing the belly down makes thick lines. Changing pressure during a stroke makes tapers.
- A value strip goes from strong paint to clear water, adding water step by step and stirring each time.